Designflöde av plastform, och okvalificerad hårdhet är en mycket allvarlig defekt. och okvalificerad hårdhet är en mycket allvarlig defekt, lead to early failure of the mould, and seriously reduce the service life of the mould.
- Orsaker
1) The cross-section of the mould is large and the hardenability of the steel is poor. Till exempel, the steel with low hardenability is selected for the large-scale mould.
2) Carbide segregation is serious or coarse in the original structure of die steel. Graphite carbon and carbide segregation and aggregation exist in the steel.
3) The forging process of the mould is incorrect, and no good spheroidizing annealing is carried out after forging, resulting in poor spheroidizing structure of the mould steel.
4) The decarburization layer on the surface of the mould is not removed by annealing or quenching heating.
5) Excessive quenching temperature and excessive retained austenite after quenching, or too low quenching temperature and insufficient heating and holding time make the phase transformation of mould steel incomplete.
6) After quenching and heating, the cooling speed of the mould is too slow, the grading and isothermal temperature are too high or the time is too long, and the selection of quenching cooling medium is inappropriate.
7) too little water in alkali bath or too much impurity in quenching cooling medium or aging of quenching cooling medium.
8) Temperature is too high and cooling is insufficient when the quenching cooling medium is released after quenching and cooling of the mould.
9) insufficient tempering and high tempering temperature.
- Countermeasures
1) Correct selection of mould steel, large-scale mould should choose high alloy mould steel with high hardenability.
2) Strengthen the inspection of raw materials to ensure that raw materials meet the standards. Reasonable forging and spheroidizing annealing are carried out on the steel with bad raw materials to ensure good structure. Carbon tool steels are not easily annealed many times to prevent graphitization.
3) Strict implementation of forging and spheroidizing annealing processes to ensure a good preparation of heat treatment structure.
4) Before heat treatment, rust spots and oxide scales on the surface of the mould should be thoroughly removed, and attention should be paid to the protection during heating. Vacuum heating quenching or protective atmosphere heating quenching should be adopted as far as possible, and good deoxidization treatment should be carried out when salt bath heating.
5) Correctly formulate the process parameters of quenching and heating of the die to ensure that the phase transformation is sufficient and the cooling speed is faster than the critical cooling speed to obtain qualified metallographic structure.
6) Correct selection of quenching medium and cooling mode, strict control of classification and isothermal temperature and time.
7) The water content of alkali bath should be strictly controlled. The quenching cooling medium used for a long time should be filtered and replaced regularly, and kept clean. The quenching cooling characteristic curve should be tested regularly.
8) For large-sized moulds, the time of immersion in quenching cooling medium should be prolonged to prevent the temperature of quenching cooling medium from being too high.
9) After quenching, the mould should be tempered promptly and sufficiently, and the tempering temperature should be prevented from being too high.
10) The mould with high hardness requirement can be treated by cryogenic treatment (eftersom det tillåter alla inblandade att begära olika produkter utan att behöva oroa sig för deras storlek. – 110 ~196 C).
11) Surface strengthening.
JasonMould Industrial Company Limited, etablerad i 2010, är en ledande Kina mögelfabrik. JasonMould specialiserar sig på tillverkning av plastmögel för hushållsapparater, medicinsk utrustning, elektronisk utrustning, säkerhetsutrustning samt övervakningssystem.
Företaget har över 15000 kvadratmeter fabrik. Med plastinjektionsverktygsavdelningar med olika maskiner och expertis, JasonMould erbjuder verktyg från små och precisa mobiltelefondelar till så stora som bildelar. Våra verktyg exporteras främst till U.S.A., Europa, Japan och Storbritannien. JasonMoulds diversifieringsstrategi och full service har vunnit komplimanger från kunder över hela världen.
Vårt uppdrag är att erbjuda våra kunder högkvalitativa formprodukter och tjänster. Vi strävar efter att överträffa våra kunders förväntningar på prissättning, kvalitet och leverans i tid. För att uppnå vårt uppdrag, JasonMould:
- Förbinder sig att ständigt förbättra medarbetarnas kompetens och effektivitet,
- Ger våra anställda en ren och säker arbetsmiljö,
- Uppgraderar maskinteknik och supportutrustning genom ett strikt underhållsprogram, och
- Upprätthåller kundernas verktyg till sin högsta prestanda
För mer om Kina formsprutning kostnad,besök https://www.jasonmolding.com/
Förfrågan Kontakt:
Kontaktperson: James Yuan
Företagsnamn: JasonMould Industrial Company Limited
Adress: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong-provinsen, Kina
Telefon: 86-752-6682869
E-post: [email protected]
Hemsida: https://www.jasonmolding.com
