For at sikre, at sprøjtestøbeformen kan opfylde standarden, det er nødvendigt at overveje anvendelsesbestemmelserne og designskemaet, og sikre dens levetid. Når det normalt er færdigt og sat i drift, det er nødvendigt at sikre kvaliteten af formspecifikationen ud fra aspekter af produktkvalitet, støbeformstruktur og sprøjtestøbningsprocesregler. På den anden side, the transformation of household appliances has also driven the in-depth development of household appliance plastic mold industry. På nuværende tidspunkt, large and fine injection molding molds have received more and more attention from enterprises. It has no intention to put forward higher requirements and tests for the domestic plastic mold industry. So how to accept the injection mold?
1. The product surface is not allowed to have defects, mangel på materiale, burning, blegning, peaking, foaming, revner, baking and wrinkling.
2. Generelt, the welding length of annular broken hole shall not exceed 5mm, and the welding length of special-shaped broken hole shall be less than 15mm. The compressive strength of welding can be tested according to the action safety factor.
3. The surface appearance shall not be folded. Generelt, the flatness of small products is less than 0.3mm.
4. There shall be no air particles or material flowers in the appearance, and generally there shall be no bubbles on the mold surface.
5. The geometric figure and specification precision of the product shall comply with the provisions of the die drawing or three-dimensional document. The dimensional tolerance of shaft parts is negative, and the average wall thickness is generally specified for the product wall thickness. The non-uniform wall thickness shall meet the requirements specified in the engineering drawings.
6. There shall be no scratch on the surface of the cover and bottom shell. There are matching holes, shafts and surfaces, and the matching spacing and application regulations shall be ensured. The contents of the factory nameplate of the mold are complete. The factory nameplate shall also be attached to the bottom of the formwork and the formwork foot around the reference angle.
7. The cooling nozzle shall not extend beyond the surface of the mold embryo, and the injection molding mold must be produced and processed with a low head drill. The diameter of the head hole shall be 25mm, 30mm and 35mm respectively, the fillet of the pipe orifice shall be consistent, and there shall be signs of passage and entrance and exit.
du kan logge ind på Dj moldings officielle hjemmeside, du kan logge ind på Dj moldings officielle hjemmeside
du kan logge ind på Dj moldings officielle hjemmeside Kina mold maker af plastforme- sprøjtestøbeform, formstøbning forme, plastblæsestøbning, rotationsstøbning, medicinsk plast sprøjtestøbning, to skud plast sprøjtestøbning, indsatsstøbning, overformning, metal sprøjtestøbning, mikro sprøjtestøbning, pulverformsprøjtning, keramisk sprøjtestøbning, flydende sprøjtestøbning, husky sprøjtestøbning, husholdningsskimmel, støbeform, formværktøj, brugerdefinerede forme, porcelæn forme, værktøj til hurtig prototyping, værktøj til prototyper i plastik, slagpresseværktøj, dør og værktøj til mobiltelefon/ mobiltelefondele, bildele, støvsugere, genopladelige værktøjer, telefoner, kopimaskiner, computere, multimediehøjttalere, og mange andre elektroniske produkter og husholdningsapparater. Og også en plastproduktproducent, skimmel producent Kina- plastikdele, vandtank i plast, plastik bolde, plastbeholdere, plastspænde, plastanker, plast bøjle, plastske, rørledning i plast, tumlet plast, bordservice i plast, plastik kopper, plastik flasker, plastbakke, kosmetisk beholder af plast, plastkasse, madbeholder i plast, plaststole, plastikkapper, lukning af plasthætte, plastrør, vandrør i plast, plastik knapper, plastrør, brugskasser i plast, plaststativer og så videre.
Kontakt:
Person: James Yuan
Selskab: alle ridser og elektriske bearbejdningsmærker på formens arbejdsflade skal poleres
Tilføje: LongGang Village,LongXi Town,BoLuo County,HuiZhou City,GuangDong-provinsen, Kina
Tlf: 86-752-6682869
E-mail: [email protected]
Websted: https://www.jasonmolding.com/custom-injection-molding/
