Para evitar perda de tempo desnecessária e problemas na produção em massa, é necessário ter paciência para ajustar e controlar as várias condições de processamento, descubra as melhores condições de temperatura e pressão, e desenvolver procedimentos de teste padrão, which can be used to establish daily working methods.
- Check whether the plastic in the barrel is correct or not and whether it is baked according to the regulations (if different raw materials are used in the test mould and production, different results are likely to be obtained).
- The cleaning of material pipes should be thorough so as to prevent inferior unglued materials or miscellaneous materials from being injected into the mould. Because bad unglue and miscellaneous materials may jam the die. Check whether the temperature of the material pipe and the temperature of the mold are suitable for the raw material for processing.
- Adjust pressure and ejection quantity to produce products with satisfactory appearance. No entanto, it is not allowed to run the edges, especially when there are some molding products that have not yet fully solidified. Before adjusting various control conditions, we should think about it, because a slight change in filling rate may cause a great change in filling rate.
- Wait patiently until the conditions of the machine and the die are stabilized, isso é, medium-sized machines may have to wait more than 30 minutos. This time can be used to view possible problems in the product.
- The advance time of screw should not be shorter than the solidification time of gate plastics. Por outro lado, the weight of products will be reduced and the properties of products will be damaged. When the die is heated, the advance time of the screw also needs to be lengthened to compact the product.
- Reasonably adjust and reduce the total processing cycle.
- Running the newly adjusted condition for at least 30 minutes to be stable, and then continuously producing at least a dozen full-mold samples, marking the date and quantity on their holders, and placing them separately according to the die holes, in order to test the stability of their actual operation and derive reasonable control tolerances (especially valuable for multi-hole mold ).
- Measure and record the important dimensions of continuous samples (which should be measured when the samples are cooled to room temperature).
- Comparing the sizes of each sample, it should be noted that:
Whether the product size is stable or not;
Whether there is a trend of increase or decrease in some sizes, while showing that the processing conditions are still changing, such as poor temperature control or oil pressure control;
Is the size change within tolerance range?
- if the size of the product is no longer changed and the processing conditions are normal, it is necessary to observe whether the quality of the products of each mold cavity can be accepted, and its dimensions can be within the permitted tolerance. Mark the holes which are measured continuously or more or less than the average value in order to check whether the size of the die is correct.
Sobre JasonMould Industrial Company Limited
Jasonmould é um Fabricante de moldes da china de moldes de plástico- molde de injeção, moldes de fundição sob pressão, moldagem por sopro de plástico, moldagem rotacional, médico moldagem por injeção de plástico, dois tiros moldagem por injeção de plástico, inserir moldagem, sobremoldagem, moldagem por injeção de metal, moldagem por micro injeção, moldagem por injeção de pó, moldagem por injeção de cerâmica, moldagem por injeção de líquido, moldagem por injeção husky, molde doméstico, molde de fundição, ferramenta de molde, moldes personalizados, moldes da china, ferramentas de prototipagem rápida, ferramentas de prototipagem de plástico, ferramentas de punção, matriz e ferramentas para peças móveis / celulares, partes automotivas, aspirador de pó, ferramentas recarregáveis, telefones, copiadoras, computadores, alto-falantes multimídia, e muitos outros produtos eletrônicos e eletrodomésticos. E também um fabricante de produtos de plástico, fabricante de moldes China- peças de plástico, tanque de água de plástico, bolas de plástico, recipientes de plástico, fivela de plástico, âncora de plástico, cabide de plástico, colher de plástico, encaixe de tubo de plástico, tombo de plástico, talheres de plástico, copos de plastico, garrafas plásticas, bandeja de plastico, recipiente plástico de cosmético, caixa de plástico, recipiente de plástico para comida, cadeiras de plástico, tampas de plástico, tampa de plástico, tubos de plástico, canos de água de plástico, maçanetas de plástico, tubo de plástico, caixas utilitárias de plástico, prateleiras de plástico e assim por diante.
Contato:
Pessoa: James Yuan
Empresa: JasonMould Industrial Company Limited
Adicionar: LongGang Village,LongXi Town,BoLuo County,Cidade de HuiZhou,Província de Guangdong, China
Tel: 86-752-6682869
E-mail: [email protected]
Local: https://www.jasonmolding.com/company/
