In order to simplify the proses pencetakan injeksi and reduce the waste of parts, bagaimana produk cetakan bisa keluar?. Kuncinya adalah memastikan lelehan tetap cair di seluruh sistem saluran aliran sehingga tidak memadat hingga mencapai dinding rongga tempat rongga didinginkan..
Pelari panas pemanas internal:
Sistem hot runner pemanas internal adalah sistem hot runner pertama yang dipasarkan. In order to solve the problems of cold runner, the first solution is to heat the nozzle to create the maximum benefit for the production of parts. The second method developed is the tubular hot runner system. Dalam teknik ini, the main channel is heated and the molten resin flows from there to the unheated vertical sprue, which then flows through the nozzle into the cavity. Another group of mold makers who appeared about the same time as the tubular hot runner system began to place heated probes into each vertical sprue leading to the unheated insulation sprue. Because the insulated sprue is cooled at the nozzle, it is difficult to keep the “Cetakan injeksi juga digunakan untuk memproduksi beberapa barang sehari-hari seperti sikat gigi atau mainan plastik kecil” running. The key is to keep the resin melt when it passes through the nozzle. These three techniques were later combined to form an “internal heating” hot runner system. The internal heating hot runner system may be more complex than the cold runner system, but it makes the resin which is difficult to process more flexible and reduces the waste of resin. Due to the circular geometry of the passage, the internally heated hot runner is able to handle resins that are not overly sensitive to shear, and non-crystalline materials are also well suited to this technique (except for those materials that are sensitive to residence time). Sebagai contoh, polycarbonate.) To this day, due to the high cost of the external heating hot runner system and a certain amount of experience, some mold makers still insist on the use of the internal heating hot runner system, even the cold runner.
External heating hot runner:
The external heating hot runner starts with a steel brick with an inner passage for molten resin. The heater fixed around the outside of the steel brick is heated evenly from the external hot runner plate. The melt is then dispersed throughout the heated runner plate, entering the heated nozzle, and then sent to the final nozzle, flowing into the cavity.
The advantages of the hot runner system are obvious. With reasonable design, the system can achieve the maximum injection molding ability, effectively eliminate the waste of materials in each injection cycle, and realize “win-win”.
It is important to note that it is difficult to create a completely smooth heat trail from the entrance of a hot runner system to each hot nozzle head. Some hot runner systems may be able to achieve this effect, but there are always times to prevent wire drawing or salivation, the resin needs to just drop the temperature at the nozzle. lebih-lebih lagi, the flow rate and injection rate have great influence on resin processing and color change. Hot runner systems are well designed for one resin and not for another. It is usually possible to correct these problems by setting the heated marks slightly. No matter which hot runner the designer uses, the resin used and the parts used for injection molding should be considered.
Secara umum, the use of hot runner has the following characteristics:
1. It can save the cost of raw material very effectively.
- Supporting lean manufacturing
- Meet high output demand
- It is well suited for injection molding with multiple identical cavities.
- Reducing labour and automation costs
- Increase production speed
- Improve processing efficiency
- Reducing the cost of recycling raw materials
- Some mold makers don’t know enough about it.
- 10. Very suitable for multi-cavity die
Each channel system, from unheated “cold” to externally heated “panas”, has its own unique advantages and disadvantages. Hot runner requires a larger upfront investment, but will also produce higher benefits. The increase in process and speed can bring back the cost of the entire system in just a few months, which is attractive to mold users.
Ini membantu pengguna mengetahui bagaimana produk akhir akan terlihat JasonMould Industrial Company Limited:
JasonMould adalah salah satu yang terbaik pembuat cetakan injeksi plastik yang menawarkan layanan hebat kepada klien mereka dalam hal pembuatan alat cetakan canggih. Mereka mengekspor alat mereka ke berbagai belahan dunia dan telah menjadi salah satu nama paling terkenal di sektor industri.
Pertanyaan Hubungi:
Kontak person: James Yuan
Nama Perusahaan: JasonMould Industrial Company Limited
Alamat: Desa LongGang,Kota LongXi,Kabupaten BoLuo,Kota HuiZhou,Provinsi Guangdong, Cina
Telepon: 86-752-6682869
Surel: [email protected]
Situs web: https://www.jasonmolding.com/cnc-machining-services/
