buikspieren, de aankoop van Commodity Factory is niet noodzakelijk beperkt tot spuitgietmatrijs, de aankoop van Commodity Factory is niet noodzakelijk beperkt tot spuitgietmatrijs. de aankoop van Commodity Factory is niet noodzakelijk beperkt tot spuitgietmatrijs, de aankoop van Commodity Factory is niet noodzakelijk beperkt tot spuitgietmatrijs, zoals slagvastheid, hittebestendigheidsgraad, vlamvertragende kwaliteit, transparant cijfer, versterkte rang, galvaniseren kwaliteit, enzovoort., als het wordt gemengd met andere kunststoffen of additieven.
De vloeibaarheid van ABS bevindt zich tussen PS en pc. the fluidity of ABS is related to injection temperature and pressure. The influence of injection pressure is slightly greater. Daarom, higher injection pressure is often used to reduce melt viscosity and improve filling performance.
1. Treatment of plastics
The water absorption rate of ABS is about 0.2% – 0.8%. For general grade ABS, bake in oven at 80-85 ℃ voor 2-4 hours or in drying hopper at 80 ℃ voor 1-2 hours before processing. For heat-resistant ABS with PC component, the drying temperature should be adjusted to 100 ℃, and the specific drying time can be determined by extrusion. Het aandeel gerecycleerde materialen mag niet hoger zijn dan 30%, and the recycled materials should not be used for electroplating ABS.
2. Selection of injection molding machine
The standard injection molding machine of Ramada can be selected (the length diameter ratio of screw is 20:1, the compression ratio is greater than 2, and the injection pressure is greater than 1500bar). If the color masterbatch is used or the appearance of the product is high, the screw with a smaller diameter can be selected. The clamping force is determined according to 4700-6200t / m2, which depends on the plastic grade and product requirements.
3. Vorm- en poortontwerp
Mold temperature can be set at 60-65 ℃. The channel diameter is 6-8mm. The gate width is about 3 mm, the thickness is the same as the product, and the gate length is less than 1 mm. The exhaust hole is 4-6mm wide and 0.025-0.05mm thick.
4. Smelttemperatuur
It can be accurately determined by air injection. According to different grades, the melt temperature is also different. It is suggested to set as follows:
Impact grade: 220 ℃ – 260 ℃, 250 ℃ is better
Electroplating grade: 250 ℃ – 275 ℃, 270 ℃ is better
Heat resistant grade: 240 ℃ – 280 ℃, 265 ℃ – 270 ℃
Flame retardant grade: 200 ℃ – 240 ℃, 220 ℃ – 230 ℃ is better
Transparent grade: 230 ℃ – 260 ℃, 245 ℃ is better
Glass fiber reinforced grade: 230 ℃ – 270 ℃
For products with high surface requirements, higher melt temperature and mold temperature are used.
5. Injection rate
The fire grade should use slow speed, and the heat grade should use fast speed. If the surface requirement of the product is high, the shooting speed of high-speed and multi-stage injection should be controlled.
6. Tegendruk
In het algemeen, the lower the back pressure is, des te beter. The commonly used back pressure is 5bar. The dyeing material needs higher back pressure to make the color mixing uniform.
7. Residence time
Onnodig te vragen 265 ℃, the residence time of ABS in the melt can not exceed 5-6 minutes at most. The flame retardant time is shorter. If the machine needs to be stopped, the set temperature should be lowered to 100 ℃ first, and then the general-purpose ABS can be used to clean the glue cartridge. The cleaned mixture should be put into cold water to prevent further decomposition. If you need to change from other plastics to ABS material, you need to use PS, PMMA or PE to clean the glue cartridge. Some ABS products have no problem when they are just demoulded, and they will change color after a period of time, which may be caused by overheating or too long residence time of the plastic in the melt cartridge.
8. Post treatment of products
General ABS products do not need post-treatment, only electroplating grade products need to be baked (70-80 ℃, 2-4 uur) to passivate the surface traces, and the products that need to be electroplated can not use mold release agent, and the products should be packed immediately after they are taken out.
9. Matters needing special attention during molding
There are several grades of ABS (especially flame retardant grade). After plasticization, the adhesive force of the melt on the screw surface is very large, and it will decompose after a long time. When the above situation occurs, it is necessary to pull the homogenizing section and compression screw out for wiping test, and regularly clean the screw with PS, enzovoort.
Over JasonMould Industrial Company Limited
Jasonmould is een Chinese matrijzenmaker van plastic mallen- spuitgietmatrijs:, spuitgietmatrijzen, kunststof blaasvormen, rotatiegieten, medisch spuitgieten van kunststof, twee schoten spuitgieten van kunststof, invoegen lijstwerk, overmolding, metalen spuitgieten, micro-spuitgieten, poeder spuitgieten, keramisch spuitgieten, vloeibare spuitgieten, husky spuitgieten, huishoudelijke schimmel, gietvorm, matrijs gereedschap:, aangepaste mallen, Chinese mallen:, tooling voor snelle prototyping, kunststof prototyping gereedschap, ponsmachine tooling, sterven en tooling voor mobiele/mobiele telefoon onderdelen, auto-onderdelen, stofzuigers, oplaadbare gereedschappen, telefoons, kopieerapparaten, computers, multimedia speakers, en vele andere elektronische producten en huishoudelijke apparaten. En ook een fabrikant van plastic producten, schimmelfabrikant China– kunststof onderdelen, plastic watertank, plastic ballen, plastic containers, plastic gesp, plastic anker, plastic hanger, Plastic lepel, plastic pijp montage:, plastic tuimelen, plastic servies, plastic bekers, plastic flessen, plastic dienblad, plastic cosmetische container, plastic verpakking, plastic voedselcontainer, plastic stoelen, plastic doppen, plastic dop sluiting, plastic buizen, kunststof waterleidingen, plastic knoppen, plastic buizen, plastic gebruiksdozen, plastic rekken enzovoort;.
Contact:
Persoon: James Yuan
Bedrijf: JasonMould Industrial Company Limited
Toevoegen: LongGang Village,LongXi Town,BoLuo County,HuiZhou-stad,Provincie GuangDong, China
Tel: 86-752-6682869
E-mail: [email protected]
website: https://www.jasonmolding.com/custom-injection-molding/
