Sebab mengapa tanda udara mudah muncul di salur masuk air bahagian PC telah diterangkan sebelum ini, yang disebabkan oleh kelajuan suntikan gam yang terlalu cepat. Oleh itu, untuk menyelesaikan masalah tanda udara di salur masuk air, we must try to reduce the injection speed without producing chatter marks and material shortage.
Atas sebab ini, we should first ensure that the melt temperature is high enough. In the case of no discoloration and no scorching, we should try our best to increase the melt temperature to 310 ℃ (for pc7025a and pc1250y materials).
Kedua, and most importantly, the mold cavity temperature must be raised to 90-110 ℃. In production, the cooling water can be turned off to raise the temperature of the mould with core.
When the mold temperature rises to more than 90 ℃, the injection can be carried out at a very slow speed, and the air marks in the injection parts will gradually fade with the decrease of the injection speed until they disappear. When the melt glue flows through the area where the air marks are formed, it must be turned back to high-speed and high-pressure injection immediately, otherwise the injection parts will produce chatter marks and lack of material.
It should be noted that the mold temperature should not rise too high. If the temperature exceeds 120 ℃, the injection parts will shrink easily, the cooling time will be prolonged, and the production speed will become very slow. Pada masa yang sama, the service life of the mold will be shortened because of the high mold temperature, and the surface of the injection parts may even have the problem of dull color.
For the safety of workers, it is best not to use hot oil machine to increase the mold temperature. Because if the temperature of hot oil is adjusted to above 90 ℃, once there is oil leakage, the consequences will be unimaginable. Oleh itu, if you want to use hot oil engine, you must pay attention to safety.
If the beer piece is thin and big, the heat of the melt will dissipate very quickly, and the heat is also very limited. It is difficult for the mold temperature to rise, and it is a problem whether the material can go well. Pada masa ini, we need to add heating tube in the mold to achieve the purpose of heating. Pada masa yang sama, it is necessary to increase the width of the water inlet to increase the flux and reduce the filling time, so as to fill the mold cavity and eliminate the gas streak.
If the mold can be changed to hot water port design, it will be very helpful to solve the problem of gas grain.
Mengenai JasonMould Industrial Company Limited
Jasonmould adalah Pembuat acuan China dari acuan plastik- acuan suntikan, acuan pemutus mati, acuan plastik, acuan putaran, perubatan pengacuan suntikan plastik, dua pukulan pengacuan suntikan plastik, masukkan acuan, terlalu banyak, pengacuan suntikan logam, pengacuan suntikan mikro, pengacuan suntikan serbuk, pengacuan suntikan seramik, pengacuan suntikan cecair, acuan suntikan husky, acuan isi rumah, acuan pemutus, alat acuan mati, acuan khas, acuan cina, perkakas prototaip pantas, perkakas prototaip plastik, perkakas penebuk, mati dan perkakas untuk bahagian telefon bimbit / telefon bimbit, bahagian automotif, pembersih vakum, alat yang boleh dicas semula, telefon, mesin penyalin, komputer, pembesar suara multimedia, dan banyak produk elektronik dan perkakas rumah yang lain. Dan juga pengeluar produk plastik, pengeluar acuan China- bahagian plastik, tangki air plastik, bola plastik, bekas plastik, gesper plastik, sauh plastik, penyangkut plastik, sudu plastik, pemasangan paip plastik, plastik jatuh, pinggan mangkuk plastik, cawan plastik, botol plastik, dulang plastik, bekas kosmetik plastik, sarung plastik, bekas makanan plastik, kerusi plastik, penutup plastik, penutup penutup plastik, tiub plastik, paip air plastik, tombol plastik, tiub plastik, kotak utiliti plastik, rak plastik dan sebagainya.
Hubungi:
Orang: James Yuan
Syarikat: JasonMould Industrial Company Limited
Tambah: Kampung LongGang,Bandar LongXi,Daerah BoLuo,Bandar HuiZhou,Wilayah GuangDong, China
Tel: 86-752-6682869
E-mel: [email protected]
Tapak: https://www.jasonmolding.com/custom-injection-molding/
