Kawalan suhu
Suhu tong: proses pengacuan suntikan to control the temperature of the barrel temperature, suhu muncung dan suhu acuan. Dua jenis suhu pertama terutamanya mempengaruhi pemplastikan dan pengaliran plastik, dan yang terakhir terutamanya mempengaruhi aliran dan penyejukan plastik. Setiap plastik mempunyai suhu aliran yang berbeza, dan suhu aliran dan suhu penguraian plastik yang sama berbeza-beza bergantung pada sumber atau jenama, due to the difference in average molecular weight and molecular weight distribution. The plasticizing process of plastics in different injection machines is different, so the temperature of the selected cartridge is different.
Suhu muncung: nozzle temperature is usually slightly lower than the top temperature of the barrel to prevent the “air liur” that may occur in the straight-through nozzle. The nozzle temperature should not be too low, Kelegaan di sekeliling sisipan bukan sahaja sesuai untuk ekzos semasa pengacuan, the nozzle will be blocked by the early solidification of the melt, or the properties of the product will be affected by the injection of the early solidification into the die cavity.
Suhu acuan: mold temperature has a great impact on the internal properties and apparent quality of products. Mold temperature depends on the crystallinity of plastics, saiz dan struktur produk, keperluan prestasi, dan keadaan proses lain (suhu cair, injection speed and injection pressure, kitaran acuan, dan lain-lain.)
Pressure control
Injection pressure includes plasticizing pressure and injection pressure, and directly affects plastic plasticization and product quality.
When a screw injector is used, the pressure on the top of the screw is called plasticizing pressure, also known as the back pressure, when the screw rotates and recovers. This pressure can be adjusted by the relief valve in the hydraulic system. In injection, the size of the plasticizing pressure needs to change with the design of the screw, the quality requirements of the product and the type of plastic. If these conditions and the rotating speed of the screw do not change, increasing the plasticizing pressure will strengthen the shearing effect. The melt temperature will be increased, but the plasticizing efficiency will be reduced, the countercurrent and leakage will be increased, and the driving power will be increased.
Sebagai tambahan, increasing the plasticizing pressure can make the melt temperature uniform, the color mixture uniform and the gas discharged from the melt. In general operation, the determination of plasticizing pressure should be as low as possible on the premise that the quality of the product is good. The specific value varies according to the type of plastics used, but usually rarely exceeds 20 kg / square centimeter.
Tekanan suntikan: in current production, the injection pressure of almost all injection machines is plastic at the top of the plunger or screw
The applied pressure (converted from the oil line pressure) shall prevail. The role of injection pressure in injection molding is to overcome the flow resistance of plastic flowing from the cylinder to the cavity, to give the filling rate of the melt material and to compaction the melt material.
kitaran acuan
Forming cycle: forming cycle directly affects labor productivity and equipment utilization. Oleh itu, in the production process, the quality should be guaranteed, as far as possible to shorten the molding cycle of the relevant time. Injection time and cooling time are the most important factors in the whole molding cycle, which have a decisive effect on the quality of the product. The filling time in injection time is inversely proportional to the filling rate, and the filling time in production is generally about 3-5 detik. The pressure holding time of injection time is the pressure time of plastic in mold cavity, which accounts for a large proportion in the whole injection time, which is usually about 20-120 detik (bahan mentah mudah terurai 5 ~ 10 minutes for extra thick parts). Before the melting material is frozen at the gate, the pressure holding time has an effect on the accuracy of the product size, and if it is later, it will have no effect on the size accuracy of the product. The pressure-holding time also has the most favorable value, which is known to depend on the feed temperature, suhu acuan, and the size of the main channel and gate. If the dimensions and process conditions of the main channel and gate are normal, the pressure value of the minimum range of shrinkage of the product is usually obtained. The cooling time mainly depends on the thickness of the product, the thermal properties and crystallization properties of plastics, and mold temperature. The end point of cooling time should be based on the principle that no change will be caused when the product is demoulded. The cooling time is generally between 30 dan 120 detik, and the cooling time is unnecessary. It not only reduces the production efficiency, but also causes difficulties in demoulding for complex parts. Demoulding stress will even be produced when the mold is forced to be demoulded. Other times in the forming cycle are related to whether or not the production process is continuous and automated, and the degree of continuity and automation.
Tentang JasonMould Syarikat Perindustrian Berhad
Jasonmould adalah pengeluar acuan plastik- acuan suntikan, acuan pemutus mati, acuan plastik, acuan putaran, Prototaip Pantas, pengacuan suntikan plastik dua pukulan, masukkan acuan, terlalu banyak, pengacuan suntikan logam, pengacuan suntikan mikro, pengacuan suntikan serbuk, pengacuan suntikan seramik, pengacuan suntikan cecair, acuan suntikan husky, acuan isi rumah, acuan pemutus, alat acuan mati, acuan khas, acuan cina, perkakas prototaip pantas, perkakas prototaip plastik, perkakas penebuk, mati dan perkakas untuk bahagian telefon bimbit / telefon bimbit, bahagian automotif, pembersih vakum, alat yang boleh dicas semula, telefon, mesin penyalin, komputer, pembesar suara multimedia, dan banyak produk elektronik dan perkakas rumah yang lain. Dan juga pengeluar produk plastik- bahagian plastik, tangki air plastik, bola plastik, bekas plastik, gesper plastik, sauh plastik, penyangkut plastik, sudu plastik, pemasangan paip plastik, plastik jatuh, pinggan mangkuk plastik, cawan plastik, botol plastik, dulang plastik, bekas kosmetik plastik, sarung plastik, bekas makanan plastik, kerusi plastik, penutup plastik, penutup penutup plastik, tiub plastik, paip air plastik, tombol plastik, tiub plastik, kotak utiliti plastik, rak plastik dan sebagainya.
Hubungi:
Hubungi orang: James Yuan
Nama syarikat: JasonMould Industrial Company Limited
Alamat: Kampung LongGang,Bandar LongXi,Daerah BoLuo,Bandar HuiZhou,Wilayah GuangDong, China
Telefon: 86-752-6682869
E-mel: [email protected]
Laman web: https://www.jasonmolding.com
