Havalandırma yuvası iki amaca hizmet eder: 1. Erimiş plastik malzemenin enjeksiyon işlemi sırasında plastik enjeksiyon kalıbından havayı boşaltın; 2. Enjeksiyon kalıplama işlemi sırasında üretilen çeşitli gazlardan kurtulun. Havalandırma yuvalarının kurulumu büyük önem taşımaktadır., özellikle ince duvarlı ürünler veya kapıdan uzak yerler için. Ek olarak, Küçük boyutlu veya hassas parçaların üretimi için havalandırma yuvalarına da çok dikkat edilmelidir., because they are able to protect the products from surface burns, yetersiz doldurma, as well as other defects.
Yani, what is sufficient air venting for plastic injection molding? Genel konuşma, if no burn marks are left on the product at the highest molten plastic injection speed, then the venting effect of the mold cavity will be considered sufficient.
Venting Methods:
There are lots of ways to vent the mold cavity, but each of them has to guarantee that: while performing venting functions, the size of the vent slot needs to be able to prevent material from entering the slot, as well as clogging at the same time. Yine de, if there are too many slots, it will do more harm than good, because if the clamping force against the mold cavity parting surface area without vent slots is too high, the cavity material will be prone to cracks, which is very dangerous. In addition to being designed on the parting surface of the mold cavity, the vent slot can also be machined in the end section of the runner system. The clearance around the ejector can also act as a way to let the trapped air out. If the height, width and position of the vent are not appropriately defined, flash will be caused, thus affecting product aesthetics and precision. Sonuç olarak, the clearance design should be able to prevent flash from occurring around the ejector pin. Özellikle, it is worth noting that molded parts like gears expect no flash at all. Öyleyse, the following venting methods should be employed:
- Completely eliminate the air in the runner;
- Apply penning treatment to the parting surface with the 200# silicon carbide abrasive, and open vent slots in the end section of the runner system, mainly referring to machining slots in the end section of the sub-channel, of which the width should be equal to that of the sub-channel while the height may vary from material from material.
Design Approach:
Based on the years of injection mold design and mold trial experience, this article is aimed to generally explain the design principles of several slot types. For parts with complicated geometric shapes, the vent slot positions should be identified after several mold trials. If a mold design adopts the integrated structure, poor ventilation will be its biggest disadvantage. Yani, for molds with integrated cavity and core, the following venting methods can be adopted:
(1) Make use of the slot or insert location in the mold cavity;
(2) Make use of the lateral insert crevice;
(3) Machine the local part into the spiral shape;
(4) When it is extremely difficult to expel the air out of the mold, an insert should be adopted. If it is not easy to machine a vent slot in some locations of a mold, such as in the corners, the insert molding process may be appropriately applied on condition that product appearance and precision are not affected. This method not only helps with venting, but is also able to lower the difficulty level for machining, and convenient for maintenance, fazla.
Vent Slot Design Dimensions:
The width of the vent slot ranges from 1.5 to 6mm, while the depth design should be able guarantee that the plastic material will not get into the slot to cause flash. Its value is dependent on the viscosity of the molten plastic, but usually its applicable range is from 0.013 to 0.05mm.
Çözüm:
Appropriately designed venting slots are able to drastically reduce injection pressure, enjeksiyon zamanı, pressure holding time and clamping force, thus making the plastic injection molding process much easier by improving production efficiency, lowering production costs and saving the energy consumed by machine.
JasonMould Industrial Company Limited Hakkında
Jasonmould bir Çin kalıp üreticisi plastik kalıpların- enjeksiyon kalıbı, döküm kalıpları, plastik şişirme, rotasyonel kalıplama, tıbbi plastik enjeksiyon kalıplama, iki atış plastik enjeksiyon kalıplama, ekleme kalıplama, aşırı kalıplama, metal enjeksiyon kalıplama, mikro enjeksiyon kalıplama, toz enjeksiyon kalıplama, seramik enjeksiyon kalıplama, sıvı enjeksiyon kalıplama, husky enjeksiyon kalıplama, ev kalıp, döküm kalıbı, kalıp aracı, özel kalıplar, Çin kalıpları, hızlı prototipleme araçları, plastik prototipleme araçları, zımba pres takımı, cep telefonu/cep telefonu parçaları için kalıp ve takımlar, Otomotiv parçaları, elektrikli süpürgeler, şarj edilebilir aletler, telefonlar, fotokopi makineleri, bilgisayarlar, multimedya hoparlörler, ve diğer birçok elektronik ürün ve ev aletleri. Ve ayrıca bir plastik ürün üreticisi, kalıp üreticisi Çin- plastik parçalar, plastik su deposu, plastik toplar, plastik konteynırlar, plastik toka, plastik çapa, plastik askı, plastik kaşık, plastik boru bağlantı parçası, plastik takla, plastik sofra takımı, plastik kaplar, plastik şişeler, plastik tepsi, plastik kozmetik konteyner, plastik kasa, plastik yemek kabı, plastik sandalyeler, plastik kapaklar, plastik kapak kapatma, plastik borular, plastik su boruları, plastik düğmeler, plastik boru, plastik yardımcı kutular, plastik raflar ve benzeri.
İletişim:
Kişi: James Yuan
şirket: JasonMould Sanayi Limited Şirketi
Ekle: Uzun Çete Köyü,LongXi Kasabası,BoLuo İlçe,HuiZhou Şehri,Guangdong Eyaleti, Çin
telefon: 86-752-6682869
E-posta: [email protected]
