De spuitgietverwerkingsfabriek zal de matrijstemperatuur verhogen;, selecteer de juiste machine voor het regelen van de matrijstemperatuur op basis van de prestaties van de grondstoffen die voor de producten worden gebruikt en de grootte van de plastic mal;, and increase the mold temperature to the temperature required for production. After the mold temperature is increased, the action of each part must be checked again, because the mold clamping phenomenon may be caused by the thermal expansion of steel, so the sliding of each part must be injected to avoid taking over and vibration.
Injection mold trial and mass production in the future, use the same raw materials as much as possible. Do not complete the mold test with secondary materials. If there is a color demand, the color test can be arranged together.
Internal stress and other problems often affect secondary processing. After the plastic mold is tested, the mold shall be processed again when the product is stable. After closing slowly, adjust the clamping pressure and act several times to check whether there is uneven clamping pressure, so as to avoid burrs and mold deformation.
Confirm the mold temperature and the inlet and outlet water temperature of the water pipe. Before injection and after injection of 10 molds and 30 mallen, measure the temperature at the inlet and outlet of each water pipe for three times. The temperature difference at the inlet and outlet of each water pipe should be no more than 3 graden. If there is any difference, immediately check the water flow and whether it is connected incorrectly.
After the above steps are checked by the staff of the injection mold processing plant, reduce the mold closing speed and mold closing pressure, set the travel distance of the safety buckle and ejector, and then adjust the normal mold closing speed. If the limit switch of large stroke is involved, if the limit switch of large stroke is involved, the mold opening stroke shall be adjusted slightly shorter, and the high-speed mold opening action shall be cut off before the large mold opening stroke. This is because the high-speed action stroke is longer than the low-speed one during the whole mold opening stroke during the mold loading of the injection mold. On the injection molding machine, the mechanical ejector rod also needs to act after the full speed mold opening action to avoid the deformation of the ejector plate due to the force on the stripping plate.
If you want to know more about injection mold, injection molding and other related knowledge of Dongguan injection mold processing factory, u kunt inloggen op de officiële website van Dj molding, Het heeft perfecte automatische productieapparatuur en complete test- en detectieapparatuur, Het heeft perfecte automatische productieapparatuur en complete test- en detectieapparatuur!
Over Huizhou Dj Molding Co., Ltd
Dj Mold is een Chinese matrijzenmaker van plastic mallen- spuitgietmatrijs:, spuitgietmatrijzen, kunststof blaasvormen, rotatiegieten, medisch spuitgieten van kunststof, twee schoten spuitgieten van kunststof, invoegen lijstwerk, overmolding, metalen spuitgieten, micro-spuitgieten, poeder spuitgieten, keramisch spuitgieten, vloeibare spuitgieten, husky spuitgieten, huishoudelijke schimmel, gietvorm, matrijs gereedschap:, aangepaste mallen, Chinese mallen:, tooling voor snelle prototyping, kunststof prototyping gereedschap, ponsmachine tooling, sterven en tooling voor mobiele/mobiele telefoon onderdelen, auto-onderdelen, stofzuigers, oplaadbare gereedschappen, telefoons, kopieerapparaten, computers, multimedia speakers, en vele andere elektronische producten en huishoudelijke apparaten. En ook een fabrikant van plastic producten, schimmelfabrikant China– kunststof onderdelen, plastic watertank, plastic ballen, plastic containers, plastic gesp, plastic anker, plastic hanger, Plastic lepel, plastic pijp montage:, plastic tuimelen, plastic servies, plastic bekers, plastic flessen, plastic dienblad, plastic cosmetische container, plastic verpakking, plastic voedselcontainer, plastic stoelen, plastic doppen, plastic dop sluiting, plastic buizen, kunststof waterleidingen, plastic knoppen, plastic buizen, plastic gebruiksdozen, plastic rekken enzovoort;.
Contact:
Persoon: James Yuan
Bedrijf: Huizhou Dj Moulding Co.,. Ltd
Toevoegen: LongGang Village,LongXi Town,BoLuo County,HuiZhou-stad,Provincie GuangDong, China
Tel: 86-752-6682869
E-mail: [email protected]
website: https://www.jasonmolding.com/custom-injection-molding/
