In order to simplify the 사출 성형 공정 and reduce the waste of parts, 대형 보조 콜드 러너의 필요성을 제거하는 것이 중요합니다.. 핵심은 캐비티가 냉각되는 캐비티 벽에 도달할 때까지 응고되지 않도록 유동 채널 시스템 전체에서 용융물이 용융된 상태로 유지되도록 하는 것입니다..
내부 가열 핫 러너:
내부 가열 핫 러너 시스템은 시장에 출시된 최초의 핫 러너 시스템입니다.. In order to solve the problems of cold runner, the first solution is to heat the nozzle to create the maximum benefit for the production of parts. The second method developed is the tubular hot runner system. In this technique, the main channel is heated and the molten resin flows from there to the unheated vertical sprue, which then flows through the nozzle into the cavity. Another group of mold makers who appeared about the same time as the tubular hot runner system began to place heated probes into each vertical sprue leading to the unheated insulation sprue. Because the insulated sprue is cooled at the nozzle, it is difficult to keep the “주기” running. The key is to keep the resin melt when it passes through the nozzle. These three techniques were later combined to form an “internal heating” hot runner system. The internal heating hot runner system may be more complex than the cold runner system, but it makes the resin which is difficult to process more flexible and reduces the waste of resin. Due to the circular geometry of the passage, the internally heated hot runner is able to handle resins that are not overly sensitive to shear, and non-crystalline materials are also well suited to this technique (except for those materials that are sensitive to residence time). 예를 들면, polycarbonate.) To this day, due to the high cost of the external heating hot runner system and a certain amount of experience, some mold makers still insist on the use of the internal heating hot runner system, even the cold runner.
External heating hot runner:
The external heating hot runner starts with a steel brick with an inner passage for molten resin. The heater fixed around the outside of the steel brick is heated evenly from the external hot runner plate. The melt is then dispersed throughout the heated runner plate, entering the heated nozzle, and then sent to the final nozzle, flowing into the cavity.
The advantages of the hot runner system are obvious. With reasonable design, the system can achieve the maximum injection molding ability, effectively eliminate the waste of materials in each injection cycle, and realize “win-win”.
It is important to note that it is difficult to create a completely smooth heat trail from the entrance of a hot runner system to each hot nozzle head. Some hot runner systems may be able to achieve this effect, but there are always times to prevent wire drawing or salivation, the resin needs to just drop the temperature at the nozzle. 더구나, the flow rate and injection rate have great influence on resin processing and color change. Hot runner systems are well designed for one resin and not for another. It is usually possible to correct these problems by setting the heated marks slightly. No matter which hot runner the designer uses, the resin used and the parts used for injection molding should be considered.
일반적으로 말하면, the use of hot runner has the following characteristics:
1. It can save the cost of raw material very effectively.
- Supporting lean manufacturing
- Meet high output demand
- It is well suited for injection molding with multiple identical cavities.
- Reducing labour and automation costs
- Increase production speed
- Improve processing efficiency
- Reducing the cost of recycling raw materials
- Some mold makers don’t know enough about it.
- 10. Very suitable for multi-cavity die
Each channel system, from unheated “cold” to externally heated “더운”, has its own unique advantages and disadvantages. Hot runner requires a larger upfront investment, but will also produce higher benefits. The increase in process and speed can bring back the cost of the entire system in just a few months, which is attractive to mold users.
에 대한 JasonMould 산업 회사 제한:
JasonMould는 최고 중 하나입니다. 플라스틱 사출 성형 업체 고급 성형 도구 제조와 관련하여 고객에게 훌륭한 서비스를 제공하는. 그들은 도구를 세계의 다른 지역으로 수출하고 산업 부문에서 가장 유명한 이름 중 하나가 되었습니다..
문의처:
담당자: 제임스 위안
회사 이름: JasonMould 산업 회사 제한
주소: 롱강 빌리지,LongXi 타운,BoLuo 카운티,혜주시,광동성, 중국
전화: 86-752-6682869
이메일: [email protected]
