Tag - china mold factory

What Is A Short Shot In Injection Molding?

A short shot is the incomplete filling of a mold cavity which results in the production of an incomplete part.
If a part short shots, the plastic does not fill the cavity. The flow freezes off before the flow paths have completely filled.
To ensure the finished part is of good quality, the part must also be adequately packed with plastic. Therefore the question to ask is not only, “Will the part fill?” but also, “Can a good quality part be made?”
Causes

Flow […]

How to maintain automotive plastic parts?

Automotive plastic parts are used more and more widely. Automotive plastic parts are not only cheap, but also environmentally friendly, beautiful, convenient and durable. Nowadays more and more automobile metal parts are replaced by plastic parts. In order to ensure the normal operation of various parts, the maintenance and maintenance of automobile plastic parts are also very important.
 
Maintenance methods of automotive plastic parts:
 

Inspection: Deformation and damage of automotive plastic parts are determined by inspection.

 

Fastening: Fastening is an important maintenance […]

Suggestions On The Maintenance Of Injection Molds

Compared with other moulds, the structure of injection moulds is more complex and precise , the operation and maintenance of the product requirements are higher, so in the entire production process, the use of positive solutions and careful maintenance, maintenance to maintain the normal production of enterprises, improve the efficiency of enterprises, has a very important significance.
 

Select the appropriate molding equipment, determine the reasonable process conditions, if the injection molding machine is too small to meet the requirements, too […]

How long does injection molding take?

The main determinant is the total number of products that customers need to produce. It takes about the same time to produce a product. Multiply the time to produce a product by the total amount of production the customer needs to produce to figure out how long it takes.
 
Material and machine preparation time should also be taken into account before formal production. The preparation time of the machine is very short, because the equipment of the injection moulding factory […]

Welding Line In Plastic Injection Molding Process

Weld Lines
The flowing defects on product surface or the linear defects that are caused when melt fronts meet each other after splitting.
Weld lines refer to the lines that occur on a plastic product surface when the cold slug melts. In areas of mold cavity where the molten plastic meets inserts or holes, areas with inconsistent flow speed/flow interruptions, where multiple flows meet or when jetting happens during mold filling, linear weld marks tend to occur due to imperfect bonding. […]

Requirements of Plastic Material for Automotive Injection Molding Parts

Excellent weather resistance, guaranteeing long-term use without color, aging cracks (including heat and oxygen aging and light aging);
 
Good chemical resistance, to resist the erosion of oil and daily chemicals;
 
Easy moulding, the injection grade material should have enough fluidity to ensure the moulding of complex components and improve production efficiency.
 
Economy requires material with high performance-price ratio.
 
Material requirements for exterior accessories
 
Weather resistance: Weather resistant materials such as AES, ASA (AAS), PC/PBT (PET) should be selected for parts that are not coated […]

Five Steps Of The Injection Mold Production Process

 With the continuous development of automotive electronics, higher requirements for product modeling,
JasonMould here shares the five steps in the injection molding process.
1. The mold structure design
A set of high-quality molds requires not only good processing equipment and skilled mold making workers. Another very important factor is good mold design, especially for complex molds. The mold design accounts for more than 80% of the mold quality.
An excellent mold design is: under the premise of meeting the requirements of customers, the […]

What factors should be considered in the design of plastic injection moulds?

Injection cost

According to the size of the machine, how much per injection, so as to determine the product ranking mode and the number of holes. The more the number of moulds produced, the lower the cost of injection moulding. Because the cost of injection moulding is calculated according to injection order.
 

Product Appearance

According to the product appearance requirements, determine the parting surface. The position of parting surface should be beneficial to die processing, exhaust, demoulding, etc. The more products, the greater […]

Injection mold development cost and how to identify a high quality mold.  

 
What is the injection mold?
Injection mold is a tool for producing plastic products; it is also a tool for imparting complete structure and precise size of plastic products. Injection molding is a processing method used in mass production of complex parts of certain shapes, specifically refers to plastics that melt by heat from injection molding machines.
High pressure is injected into the cavity, and after cooling and solidification, a molded article is obtained.
Mold application:
Mold is the basic process equipment for […]

What Plastic Parts are on The Car?

Bumper housing

Also known as “bumper”, but in fact it is only the auxiliary shell outside the bumper, not the body of the bumper. Bumper housing plays the role of cushioning and energy absorption, the working environment is relatively complex, and the volume is larger, so it is generally made of polypropylene (PP), because of its lighter weight and better corrosion resistance.
 

dashboard

 
Apart from wood and leather, the dashboards of automobiles are basically plastic, but there are differences between hard and […]