Plastic injection Mould

Discoloration of common problems in plastic injection molding

Discoloration refers to the inconsistency between the surface color of the formed parts and the required color. Discoloration may be caused by a variety of reasons, including injection molding machine, plastic mold, injection process and raw materials.
(1) Injection molding machine
① The equipment is not clean and needs cleaning. Dust or powder deposited in the barrel contaminates and discolors the material;
② Temperature control fault caused by temperature controller or heating system fault;
③ There are obstacles in the barrel, which lead […]

What will be caused when injection mold testing in many times?

The design of the injection mold was not fully collectively reviewed, and the structure of the injection mold was unreasonable, which caused the injection mold to undergo multiple improvements after the test, which made the injection mold cost exceed the budget.
If it can be solved after several improvements, it is relatively fortunate. There are many cases that are unsatisfactory, and even the injection molds have to be scrapped and reworked. This cost cannot be controlled.
There are also cases where […]

Why plastic parts have deformation when processing

In order to ensure the normal processing of plastic parts, operators need to understand the cause of the abnormal appearance in this process, the better to avoid the abnormal appearance during processing. Below, JasonMould share you the causes of deformation in processing:
 
 

During the process of molding, the surplus material is spilled into the gap between the mold and the mold surface and retained on the plastic part. A kind of linear trace on the surface of plastic parts, is […]

How to solve the surface sag in 2K mold

The basic reason for surface sag: from the perspective of plastics, when the plastic cools and shrink, insufficient filling will lead to product surface sag or internal cavity.
 
The causes and solutions of defects are different depending on the location of sag.
 

When the sag occurs at the final cooling position of the thick-walled product, or at a distance from the sprue:

 
Cause analysis: The typical thick wall and the surface sag or hole far from the sprue are usually due to […]

Causes and solutions for swelling and bubbling of injection molding parts

Some plastic parts after demoulding, have swelling or bubbling on the back of metal insert or in the extra thick parts. This is due to the expansion of the released gas under the action of internal pressure on the plastic which has not been completely cooled and hardened. JasonMould works with you for details.
 
Solutions:
 

Effective cooling. Reduce mold temperature, prolong tooling time, reduce drying and processing temperature.

 

Reduce the filling speed, reduce the forming cycle and reduce the flow resistance.

 

Increase the […]

Lettering on the surface of injection mold

We often see all kinds of patterns and Numbers on plastic pieces, and these Numbers are different. How to carve these Numbers and patterns on these molds, we have these kinds of common methods.
The first is directly through the engraving machine engraved on the mold. This is usually used when the font or pattern is large. Usually the resulting font has a knife cut on the surface and needs to be polished.
In the normal small – and medium-sized mold, […]

What information should be provided to the manufacturer for the injection molding process?

Many customers need injection molding after a product is newly designed. When a new product needs tool making, what information should the customer provide to the manufacturer?
 
JasonMould shares you a general idea of what is required for tool making and injection molding.
 

3D CAD file of product.
Bill of material ( including materials required for products and surface finishing requirements etc.)
Batch quantity.

With the above information then we can offer you an accurate price.
About JasonMould Industrial Company Limited

Jasonmould is a China mold maker of plastic […]

Common problems in injection molding insufficient filling

The main reasons for insufficient filling are as follows:
1) insufficient resin capacity.
2) insufficient pressure in the cavity.
3) resin fluidity is insufficient.
4) poor exhaust effect.
As an improvement measure, we can start from the following aspects:
1) lengthen the injection time to prevent the resin countercurrent before the gate solidification due to the short molding cycle, which makes it difficult to fill the mold cavity.
2) improve the injection speed.
3) increase the mold temperature.
4) increase the resin temperature.
5) increase injection pressure.
6) enlarge gate […]

What Are The Two Part Of a Plastic Injection Mold?

Injection molding is a processing method used in mass production of complex parts. Specific principle refers to: heat melting plastic raw materials by injection molding machine screw into the mold cavity, after cooling and curing, plastic forming products.
 
The plastic mold consists of two parts: moving mold and fixed mold. The moving mold is installed on the moving template of the injection molding machine, and the fixed mold is installed on the fixed template of the injection molding machine. During […]

How to avoid deformation in mould manufacturing

In the process of mold manufacturing, deformation often occurs, so how to avoid the deformation in mold manufacturing?
(1) the thickness of the product shall be as uniform as possible.
(2) all parts of the cooling system are designed to make the cavity temperature uniform.
(3) the pouring system can make the material flow symmetrical, avoid warping caused by contraction in different flow directions, and try to eliminate the density difference, pressure difference and temperature difference in the cavity.
(4) the thickness of […]