Plastic Injection Molding | China Plastic Injection Molding Companies With Tooling And Injection Moulding Die Makers

29 Oct

Specific requirements for injection mold maintenance

1. When replacing mold parts, recognize that the parts to be replaced are qualified;
2. Each component shall be gently knocked and slowly pressed during disassembly and installation;
3. During the installation of die inserts, the cooperative gap shall be recognized as qualified;
4. Prevent the surface of parts from warping, scratching, pits, dross, deformity, rust and other conditions;
5. If any parts are replaced, communicate and acknowledge with the mold design department in time. Pay attention to the balance of each part […]

27 Oct

How many suggestions did we mention for mold protection?

If there is no effective mold protection, the mold will be damaged. We gives you the following suggestions:
When disassembling the mold, avoid bumping and drenching, and move stably.
Spray hot mold, and then spray a small amount of release agent.
Conduct a comprehensive inspection of the mold and carry out anti rust treatment: carefully wipe out the moisture and sundries in the cavity, core, ejector and row position, and spray anti rust agent and grease on the plastic mold.
The maintenance of […]

22 Oct

Ingenious design of lifter in injection mold processing plant — solving the problem of poor assembly

The designers of the injection mold processing plant found that if there is no preset gap in the mold design, it will lead to many problems such as poor assembly and needle breakage and needle burning when ejecting the mold. So how do the mold design engineers of Dj molding solve this problem?

1. Design skills for connecting lifter: since there is no allowance for the large inclined plane of this kind of lifter, and there is no allowance for […]

20 Oct

How to improve the service life of molds? Dj molding, who has more than 10 years of experience in mold industry tells you!

No matter what object has a certain service life, the glue coated mold is no exception. When it is used to a certain extent, the mold will fail and need to be opened to produce a new mold. The service life of mold is affected by many factors. Only the mold factory with a complete understanding of these factors can suit the remedy to the case and produce a mold with a longer service life.

With the rapid development of […]

18 Oct

What are the aesthetic applications in the product design of beauty instrument injection molding production company?

Only when modern products have good quality characteristics can they meet the increasing aesthetic requirements of consumers. For the product design of beauty instrument injection molding company, it has always been our pursuit and goal to present products to customers in a more beautiful attitude.

Therefore, when designing products, our designers integrate the content and processing methods of aesthetic art into the whole product creation, and comprehensively reflect the physical beauty, linear beauty and color beauty of products by using […]

15 Oct

What are the precautions for mold test before processing in injection mold processing plant?

The injection mold processing plant shall increase the mold temperature, select the appropriate mold temperature control machine according to the performance of the raw materials used for the products and the size of the plastic mold, and increase the mold temperature to the temperature required for production. After the mold temperature is increased, the action of each part must be checked again, because the mold clamping phenomenon may be caused by the thermal expansion of steel, so the sliding […]

13 Oct

Injection mold factory’s know-how to do well in products — paying attention to injection molding process

Some products of the injection mold factory are molded with PC (polycarbonate) or PC + ABS materials. Due to the poor fluidity of PC, the process is usually filled with high mold temperature and high material temperature: the gate used is usually point gate, and graded injection molding is required to find the gate position and injection pressure maintaining switching position, It will be very helpful to solve the gate gas mark and flash anomaly.

Therefore, if our injection mold […]

11 Oct

Injection molding products appear crazing how to do, mold design to solve your worries!

The crazing defect of plastic mold injection molding plant in the process of injection molding products can not be solved after debugging by various methods. At this time, it is necessary to consider whether the solution to such problems is not considered at the beginning of mold design. Next, the machco mold designer will analyze why the mold design can solve the product crazing problem.

Through the inspection of the following four aspects, the problems of this kind of plastic […]

08 Oct

Dongguan injection molding factory expounds the product design problems

Through preliminary market research and product data provided by customers, R & D personnel and project leaders of Dongguan injection molding plant can formulate corresponding project feasibility report to accurately control the R & D progress and delivery cycle of products.
Before design, it is also necessary to understand and analyze the relevant technologies of the product. As designers, they need to timely understand and master the cutting-edge trends of relevant global technology development, and often think about how to […]

06 Oct

How do general injection molding factories solve the problem of product pitting?

Many technicians of injection molding products factories will find that sometimes there are many pits on the surface of injection molded products when plastic products are processed and injected. Different from the impurity problem of black spots, pitting mainly produces many pits on the product surface.
It has a great impact on the appearance. The inspectors of the injection molding product factory should know that it is difficult for customers to accept such products with appearance problems.
We consulted technician and […]